Your location

Your location decides your currency and the countries you can ship to.


Official Urban Iki brand store
Same-day dispatch

How do I mount the Urban Iki rear seat with frame mounting?

Can’t wait to start exploring with your child on the seat behind you? Our mounting guide tells you how to install the Urban Iki rear seat with frame mounting in a quick, simple and safe manner. If you prefer a visual guide, you can also watch our assembly video. Keep the included assembly materials at hand and learn how to assemble, install and detach your Urban Iki frame-mounted bicycle seat.

Easily attach the frame mounting bracket to your bicycle

To attach the child seat to your own bike, you’ll need the frame mounting bracket, the frame mounting block with screws, the mounting frame, an Allen key, and your own bike. Curious if the rear seat with frame mounting fits your bike? In this blog, we’ll tell you all about it.

Step 1: Assemble the Urban Iki rear seat

For this, you’ll need the two leg parts, along with the Urban Iki rear seat. Slide the two leg parts together so they are securely attached. Then place the rear seat on its back, hang down the safety strap, and slide the leg parts into the grooves on either side of the rear seat. Make sure you hear a ‘click’. This indicates that the leg parts are securely in place.

beendelen in elkaar klikken achterzitje

Step 2: Insert the bolts into the mounting block

First, place a washer around each bolt (four in total) and make sure the covers under the mounting block are closed. Then insert the bolts into the four designated holes on the top of the mounting block.

Bouten in frame montageblok

Step 3: Attach the mounting block to the frame of your bicycle

Place a dowel over the bolts and determine the correct height for the frame block by holding the bracket next to it. The frame should extend above the wheel. Tighten the bolts (clockwise) with the Allen key.

Step 4: Attach the mounting block cover

Slide the cover onto the mounting block (from top to bottom) until you hear a ‘click’.

Step 5: Click the frame mounting bracket into the frame mounting block

Now that the mounting block is securely attached to the frame of your bicycle, you can insert the frame bracket into the mounting block. Place the bracket in the designated holes on the backside. Please note: only when you hear a clear ‘click’, the frame mounting bracket is securely in place!


Attach the Urban Iki rear seat to the frame bracket in 5 simple steps

Now it’s time to mount the Urban Iki bicycle seat on the frame bracket. Keep the assembled rear seat, mounting frame, and Allen wrench at hand.

Step 1: Loosen the clamps of the mounting frame

Use the Allen wrench to loosen the hooks on the mounting frame. After loosening, you can slide the holders to make the mounting frame fit the frame mounting bracket.

Step 2: Position the mounting frame of the Urban Iki bicycle seat on the frame mounting bracket

Make sure to place the mounting frame on the frame mounting bracket. Ensure that the axle of your bike stays within the four triangles (located on top of the mounting frame).

Step 3: Screw the mounting frame onto the frame mounting bracket

Use the Allen wrench to tighten the hooks (clockwise). This firmly attaches the mounting frame onto the frame mounting bracket.

Step 4: Place the seat onto the frame mounting bracket

Good job: the mounting frame is now firmly attached to the frame mounting bracket. Get the bicycle seat for the most important step: attaching the Urban Iki bicycle seat to your bicycle.

  1. Take the safety buckle in one hand and place your other hand on the clip at the bottom of the rear seat. Make sure that the safety strap is located on top of the seat.
  2. Slide the seat horizontally over the frame, and make sure to keep the seat centered.
  3. Apply pressure to the top of the back and keep pushing down until you hear a ‘click’. Note: the seat is correctly attached when the red sticker above the clip is no longer visible!
  4. Check if the seat is securely attached by shaking it back and forth.
  5. Secure your bike seat against theft by turning and removing the key. Note: Only our latest bike seats (from March 2024 onwards) are equipped with an integrated lock with a key.

Step 5: Adjust the seat to your likings

Now that the seat is securely in place, adjust the footrests to the correct height by lifting the levers at the back of the leg parts.

The shoulder straps can be adjusted to two heights and tightened or loosened using the buckles.

Easyfix montage afstellen

How do I detach the frame-mounted Urban Iki rear seat?

The Urban Iki bicycle seat is easy to detach. This allows you to cycle without a seat when you go out without your child.

Step 1: Take the seat from the mounting frame

Unlock the rear seat. Release the safety strap around the frame of your bike. Grasp the bike seat by the buckle, press down the seat clip, and pull the attachment slide that you feel at the bottom backward to remove it from the bike. It’s as simple as that!

Step 2: Remove the frame mounting bracket from the mounting block

Press the square black cap of the frame mounting block slightly down to remove the frame mounting bracket.

Watch our video for the installation of a rear seat with frame mounting